MediaBoot Script (en)

- in Deutsch

- in English

Install a OE2.0 Image on a media device

The media-boot script by emanuel installs an image onto a media device such as USB, CF, SD or SSD, inclusive the GP3 Feed. While executing the script the device gets partitioned into 3 partitions (boot, swap and root). Subsequently the image (as tar.bz2 archive) is downloaded and unpacked onto the device. After an automatic restart of the Dreambox the image from the device is bootet and offers enough memory for all your needs. Interesting e.g. for the DM800se with small flash capacity ;) The Media-Boot Script is available in two versions. You can choose between folowing OE2.0 based images. media-boot (DMM exp. OE2.0) merlin-media-boot (Merlin 3 OE2.0) Requirements: DM500HD (needs a USB Mod), DM800se, DM8000HD, DM7020HD. A functioning internet connection. Bios of the Dreambox needs to be configured correctly. A media device larger than 1GB. Create Bootlog, if the boot fails. The media device needs to be formated in FAT32. Use other media device, if the boot fails. Mainly USB Sticks can be problematic. Media-Boot uses a pluged media device. Problems occur when plugging additional devices into the dreambox. As a result the device names move and booting is no longer possible. This problem can only be solved by making a Bootlog and editing the autoexec_*.bat. Take a look at Tips & Tricks. Bios configuration Bios - DM 8000 HD PVR Bios - DM 800 HD se You need to prepare the Bios to be able to boot via a removable media containing the FAT filesystem. The following chapter shows you the needed preparation for the different kind of Dreamboxes. The USB support needs to be activated for all Boxes. Changing the Bios Like flashing the Bios via Webbrowser you can connect to the Bios. After you see "STOP" at the display you can connect via telnet ip_of_dreambox to the Bios. Than you can change the needed values. Further informations about accessing the BIOS can be found in Wiki article The Dreambox Bios. Choose Boot Source If you cannot change the values at Boot Source between Flash / CF / USB, then use the [Page UP] or [Page Down] keys at your keyboard. Mac users can use the following combination [Fn]+[Shift]+[Arrow up/down]. The following picture shows how these keys can look ;) DM 500 HD Primary boot source: usb [/autoexec_dm500hd.bat] Secondary boot source: flash Enable USB support: [ENABLED] DM 800HD PVR Primary boot source: usb [/autoexec_dm800.bat] Secondary boot source: flash Enable USB support: [ENABLED] DM 800HD se Primary boot source: usb [/autoexec_dm800se.bat] Secondary boot source: flash Enable USB support: [ENABLED] DM 7020HD Primary boot source: usb [/autoexec_dm7020hd.bat] Secondary boot source: flash Enable USB support: [ENABLED] DM 8000HD PVR Primary boot source: usb [/autoexec_dm8000.bat] Secondary boot source: flash Enable USB support: [ENABLED] Back to table of contents Configure Media-Boot Download the wanted script from Media-Boot Thread unpack and copy the file with FTP onto the Dreambox in the directory /home/root. Make sure the script has the correct rights, otherwise it can not be executed. Use the following command when connected via Telnet_(english) or ssh. Attention this command ist for the script for the DMM exp. Image. If you use the script for Merlin, you need to replace media-boot by merlin-media-boot! chmod 755 media-boot Back to table of contents Media-Boot Script Informations Informations about Media-Boot can be displayed as follows. root@dm800se:~# ./media-boot --help media-boot: is a script to install dreambox image (OE2) on extern device >= 1GB NOTE: this script is only for advanced users! Make sure the selected device is not your harddisk!! Usage: media-boot -i /dev/sd<a-z> install image on selected device /dev/sd<a-z> Usage: media-boot -d shows avaible devices on box root@dm800se:~# Back to table of contents List the available media devices With the following command you can list the available devices. In the example (output reduced) a hard disk and a USB Stick with 8GB is found. The namaof the device is important for starting the Media-Boot script in the next step. In this example the USB Stick has the name /dev/sdb. root@dm800se:~# ./media-boot -d media-boot: found following devices on box: Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 1 60801 488384028+ 83 Linux Disk /dev/sdb: 8006 MB, 8006926336 bytes 84 heads, 6 sectors/track, 31028 cylinders Units = cylinders of 504 * 512 = 258048 bytes Device Boot Start End Blocks Id System /dev/sdb1 5 31025 7817216 b Win95 FAT32 Back to table of contents Execute Media-Boot Media-Boot is started with the following command. Make sure you use the correct device name, pay attention you don't make a mistake and specify your hard disk. Be patient, the initializing, downloading and unpacking of the image takes a while. Afterwards the box restarts automatically, and the image from the stick is bootet. You can check the availiable memory with df -h. root@dm800se:~# ./media-boot -i /dev/sdb media-boot: installing on device: /dev/sdb media-boot: stoping automount reboot to get back media-boot: stoping udev . . . Back to table of contents Install Chkbootmedia After booting the Dreambox successfully from the media device the additional package (chkbootmedia_x.xx_all.ipk) needs to be installed. This is needed to prevent overwriting the autoexec_*.bat when kernel updates are installed. This would lead to a failed boot of the media device. Download the package from hier and copy the file with FTP onto the Dreambox in the directory /tmp. Installthe package with the following commmand. opkg install /tmp/chkbootmedia* Back to table of contents Backup / Restore Image You can create or restore a backup with the following commands. The exampleuses again the media device /dev/sdb. The name of the media device can be found with the command fdisk -l. Backup Image When the image is running from the media device you can make a backup with the dd command. In this example the path for the backup refers to the hard disk and the file name is my_backup.img. The size of the backups is the same size as the used media device. The proces takes a while, please be patient and wait untill the command line shows a prompt again. dd if=/dev/sdb of=/media/hdd/my_backup.img Restore Image Start the Dreambox from Flash memory and use the following commandfor restoring. Make sure the device name is correct. Again use the command fdisk -l to double check! Make sure you use a media device which is at least the same size as the backup file (*.img). The proces takes a while, please be patient and wait untill the command line shows a prompt again. dd if=/media/hdd/my_backup.img of=/dev/sdb Back to table of contents Tips & Tricks Install the GP3.2 Plugin The script offers the possibility to install the GP3.2 Plugin, GP3 Addons or GP3-Skins. This way the BluePanel and the additional plugins and Skins are available immediately after booting the media device. Edit the script and search the following lines: EXTRA="" #EXTRA="geminiplugin geminidreamnetcast geminijukebox geminirezapp geminigweather gemininetcastwebif geminirssreader geminiwebcam" You should add the wanted packages at EXTRA="" between the quotes. The line for installing the GP3.2 Plugin, NFS Server and Gemini Jukebox looks like the following example. EXTRA="geminiplugin gemininfs geminijukebox" If you don't know the package name you can list the name when using an image with the GP3 Plugin using the following command. But before using the command do opkg update. The first command shows all GP3 packages, the second only the GP3 Skins. opkg list *gemini* opkg list *gp-skin* Back to table of contents Support thread If you need help with Media-Boot, follow the Link ;) Media-Boot Back to overview: Gemini-Wiki:English Portal or Mainpage